Snow Performance 410 POWER-MAX Water-Methanol Injection System
The Snow Performance 410 POWER-MAX Water-Methanol Injection System for your 2007.5-2015 6.7L Cummins provides your Dodge Ram with horsepower, torque and lower EGT's. The POWER-MAX system comes equipped with the boost referenced VC-50 controller and has the ability to progressively command 2 Snow Performance Hyper-Sonic Nozzles independently of one another. This sophisticated injection strategy yields a dyno proven 65+HP and 200-300 degree drop in EGTs!
The VC-50 comes with a dual 7 color LED screen and displays boost, percentage of injection, low level, and 2 fault modes (clogged line/unplugged line) directly on the screen. Utilizing a truck specific Snow Performance Injection Boot (Rated to 65 PSI) no drilling is required of the intake piping and allows the location of 2 Snow Performance Hyper-Sonic Nozzles right where you need it. If you are looking for the most advanced, high quality, U.S.A made water-methanol injection system tailored to your Diesel Truck than look no further than the Snow Performance POWER-MAX.
- Lower Exhaust Gas Temperatures
- Increased Horsepower
- Increased Torque
- 300 PSI Extreme Environment UHO (Ultra High Output) Pump
- All Tubing Necessary for Installation
- 10 ft ¼ Inch High Temp Nylon Tubing
- 36 Inches High pressure Boost Line
- 3 ft (Black) Wire Loom
- Terminated 2 1/16 Gauge Style Meth Controller
- Universal 2 1/16 Gauge Pod
- Wire Harness
- Power Solenoid Upgrade
- Bulkhead Fitting to Tap Into Stock Windshield Washer Fluid
- Diesel Injection Boot (Vehicle Specific Systems Only)
- 2 Nozzle Holder/Check Valve Combo
- 3 Snow Performance Nozzles to cover a wide range of HP
- Required Hardware Needed For Installation
- Comprehensive Instructions to Install on Any Diesel Truck
What are the benefits of Water/Methanol injection?
Boost Cooler Benefits (Diesel):
1. Greatly reduced EGT's. Decreases of 250 degrees F are common using a 50/50% Methanol /Water mix. This prevents the usual problems associated with high exhaust car temperatures - rings sticking, holed pistons, etc.
2. Low cost power - where else can you get 70-100 HP for approximately $400 along with reduced EGT's.
3. Greatly increased air charge densities - 3-5 psig boost increases are common.
4. Great for towing - more power/cooler EGT's to haul the heaviest loads.
Do I need an Intercooler with Water/Methanol injection?
Up to approximately 20 psi boost, water/methanol injection will provide all the density increase/detonation control needed in most applications. Of course, Intercooling and water/methanol injection would provide even greater benefits especially beyond 20 psi boost. Most air-to-air intercoolers are only 50-65% efficient. That means for example, that with 11psi boost and its 120f air charge temperature increase, an intercooler reduces the air charge temperature only 60 degrees. Also, an intercooler will reduce boost 2 - 4 psi. on average.
Why not use a windshield washer pump?
Water/Methanol must be injected at above 50psi to properly atomize. Lower than 50psi causes greatly reduced air charge cooling as the result of larger droplets and their reduced total surface area.
Methanol is a high octane fuel that is extremely resistant to detonation with an excellent cost/benefit ratio. ($1.50 - $2.00 per gallon.) Its high latent heat of vaporization also makes it an excellent air charge cooler which means a denser mixture and more horsepower. Because of these facts, it is a better anti-detonant than ethanol or iso-propanol although they will work in a pinch. It has however only about 60% of the energy content of gasoline by volume so about twice as much is used to make similar power if used as a straight fuel. It is extremely toxic and should be handled with rubber gloves in well ventilated areas only. Care should be taken to avoid skin contact.
How much Water/Methanol?
To prevent detonation, the ratio of Water/Methanol to gasoline is roughly 1 to 5 in gasoline applications- 1 to 4 in diesel. In practice, you give it as much water / methanol as it takes to eliminate detonation without quenching combustion. The amount depends on the onset RPM of injection, the octane of the gasoline, fuel/air ratio, cylinder head type, even the weather conditions. Your engine is actually pretty tolerant of extra water vapor, you will know it's too much when the engine misses and loses power.
Where can I purchase Methanol?
Methanol can generally be purchased where racing fuels are sold. Also, most gas line dryers like "Heat" are simply Methanol. Suppliers of industrial chemicals can also supply Methanol usually at a higher price than fuel suppliers. If all else fails, most windshield washer fluids are up to 40% Methanol and 58% water.
How long will a tank (2 qts.) last?
In high boost/high horsepower application, a full blast 1/4 mile run will utilize as much as 1/8 tank. A larger tank should be considered if over 9psi boost is utilized in road racing where a tank can be used in as few as 6 - 2 mile/ full tilt laps. Under normal street use in a 400 HP Mustang, a tank usually lasts about 500 miles. Two reservoirs can be used for 1-gal total capacity if desired. Turbo diesels use more qty. and usually utilize the existing windshield washer reservoir (over 4 qts. in most cases) or the new 8-gal reservoir upgrade. More will always be used when the system is first installed, less when the novelty wears off.
Can I use windshield washer fluid?
Although most contain some glycol and detergent, most windshield washer fluids are up to 50% alcohol (methanol, ethanol, isopropanol) and make an excellent Boost Cooler®. Try to find one that indicates "contains methanol".
At what boost level do I introduce Water/Methanol?
Centrifugal superchargers/large turbos: Generally, at 50% of peak boost the recommended quantity should be introduced. Positive displacement superchargers/ fast spooling turbos: injection should occur at or near peak boost to avoid combustion quench since peak boost occurs so fast.
What ratio of Water/Methanol is recommended?
Will water/methanol harm my engine?
A 50/50 ratio is recommended. This has been demonstrated to be the best for charge/air cooling, excellent detonation control, and controlling cylinder temperature. This includes diesel applications where water conditions the combustion of the methanol so combustion timing isn't affected.
In theory, at recommended quantities, most of the mixture is evaporated before it hits the combustion chamber. Also, injection only takes place at high boost levels minimizing cylinder wash concerns. Engines that have been torn down after two years of water/methanol usage have shown no wear issues only clean combustion chambers. In fact, water/methanol reduces the probability of engine destroying detonation. Think of it as an insurance policy against detonation.
Can the Boost Cooler® be applied to naturally aspirated and nitrous engines?
1.Naturally aspirated/high compression engines:
In this application, water/methanol injection allows the use of pump fuel in all but the most extreme situations which effects tremendous cost savings as well as horsepower increases due to air density increase and realized timing potential. The system is activated by a throttle switch so that injection takes place only during high engine loads when needed.
2. NOS engines: With NOS, water/methanol injection allows the use of full timing even with large (250HP+) quantities. Injection is controlled by the same means that controls NOS injection.
3. Naturally aspirated/stock compression: With naturally aspirated engines with less than 10:1 compression, water/methanol is used typically in warm climates to get the intake temps back to 60°f. Benefits include: 10-15 HP increases from air density increases and full timing, Increased gas mileage, and carbon free combustion chambers. Activation is by a throttle switch adjusted for onset engine load. With this application, the nozzle is sized so that no more than 10% of total fuel consumption at peak flywheel HP is injected.
Why is Water/Methanol injection so effective on Diesels?
Unlike gasoline engines, the power in a turbo diesel is largely a function of fuel. The problem with continually adding fuel is that you reach a point where the exhaust gas temperatures become prohibitive (over 1500 degrees F). A 50/50% Methanol/Water mix will decrease EGT's approximately 250f + while increasing power 70-100HP.
Power is increased through:
a. Intake charge cooling - Water/methanol will lower air charge temps over 200f in this application.
b. Methanol - this acts as a fuel as well as cooling the intake charge.
Where else can you get this kind of power with cooler EGT's!
Is this technology new with Turbo Diesel?
Water/methanol injection has been used extensively for years in high performance truck/tractor pullers. With the elevated boost levels required for peak power, water/methanol is a common means of cooling the intake charge and reducing exhaust gas temps. Also, truckers have used water injection for years to increase fuel mileage.